Not long ago, I installed a computer and was seen by a buddy. I asked him to help him also install the platform. I used the first Ma Fang Chassis. My buddies also liked it, but he felt slightly larger and asked if I had any small points. , I study, found that the Patriot popular chassis is just a small chassis than the Ark, Ark's size is:, length X width X height: 520x248x530MM; popular is long X width X height: 510x200x508MM, chassis first arrived, with We share it. The Patriot Windrunner chassis has a double-sided full-thickness design, acrylic material, and dark black color. Acrylic side panels are secured with six toolless screws. I/O interface design at the top, including dual USB 3.0, dual USB 2.0, Mic jack, Ear jack, power button, also has SDTF card reader interface, two wind speed control push and pull keys, especially worth noting there is a A button like a snowflake logo is a light adjustment button. The top of the chassis supports 120mm*2 fan installation. Of course, 240 cold rows can also be installed. The air filter uses a magnetic suction type. The front panel of the chassis is a hole and a large-area dust-proof net is used. Behind the standard is a 7-card slot in the tower. Two optical drive mounting positions remain in front of the chassis The front panel has translucent lines on the sides, which are RGB strips. The other side of the chassis is also a large area of ​​acrylic side The four legs on the four sides of the chassis have non-slip rubber; there is also a dustproof net at the bottom of the power supply. Chassis internal: support for 160mm high heat sink and 400mm long graphics card, the chassis also has "hanging" three 2.5-inch hard drive installation position, the top of the drive is detachable. The chassis comes standard with three 18-beam RGB fans (two full, one at the back), and the default is that there is no fan installed at the top. This is a bit stingy. The inside of the chassis does not use a closed power supply compartment, but at the top of the power supply installation position, a small area is reserved. There is a hollow triangular structure. I do not know whether this design has the effect of strengthening the back of the chassis, or whether it is of little use. . The top supports 240mm water cooling or two 12cm fans. Three 2.5-inch disk trays are removable. The front panel is directly removed with violence, and there are light bars on the 2 side. Two fans are installed on the front of the chassis and can support up to three 12-cm fans or 360-mm water-cooled rows. Of course, the drive cannot be installed. The back of the chassis has a separate 2.5-inch hard disk drive and two 3.5-inch hard disk drives (compatible with a 2.5-inch hard drive). A multi-function controller that controls the RGB fan revolutions and color conversion is also found in the lower center. Two 3.5-inch hard disk shelves, pay attention to have a small opening before and after, because it is free of screws, you need to put the hard disk into the buckle, with this small opening is much easier. The controller can connect up to 10 RGB fans, and it can also expand the LED light bar, which requires a large D power supply. The fan interface is a small 6 pin and is not compatible with the conventional 12 cm fan power supply. In addition, the controller can also concentrate the fan wires, so that the back line will not be too messy. Topline space: The 3.5-inch hard disk can be installed in a space of 3cm. However, if the hard disk is installed, this part is basically full, and the space behind it is about 1.5cm+, which is more general. The skeleton of the chassis. Chassis advantages: 1) The internal space is large, the heat dissipation should be good, and there is plenty of room for water cooling. 2) Standard fan and light bar, and control system. 3) The price is 100 less than the Ark. Disadvantages: 1) Only 3 fans, 2 less, not too generous. 2) The fan and light bar control system is relatively closed at 6 pin, if the conventional fan and light bar are installed, the interface is not compatible. Other hardware is purchased, the graphics card is the latest GTX1050ti, looking forward to the performance of the new graphics card
Fiber Fast Connector,Fiber Quick Connector,Fast Connect Fiber Connectors,Fiber Optic Quick Connector Ningbo Fengwei Communication Technology Co., Ltd , https://www.fengweicommunication.com
Aigo patriots esports computer case out of the box share
Optical fiber connector is a detachable (movable) connection device between optical fiber and optical fiber. It connects the two end faces of optical fiber precisely, so that the optical energy output by the transmitting optical fiber can be coupled to the receiving optical fiber to the maximum extent, and the impact on the system caused by its involvement in the optical link can be minimized. This is the basic requirement of optical fiber connector. To a certain extent, optical fiber connectors affect the reliability and performance of optical transmission systems.