3D printing on the pen machine is mainly used in 3 d printing pen, is made from a special custom Dc Gear Motor, mainly used in 3 d printing pen, pen 3 d printing machine has been updated three generations according to the requirements of product.
3D Printing Motor product introduction:
The 3D Printing Motor is based on the deceleration Motor, coupled with supporting gears and ball bearings.The role of the gear reducer is to provide lower speed and greater torque.At the same time, gear box different deceleration ratio can provide different speed and torque.It's mostly rolling.
Features: 3D Printing Motor, small size, large torque, low noise, durable, low energy consumption, customized power design, convenient installation and maintenance;
Simplify design and save space.
Features: usually used financial equipment,
office equipment, electronic locks, wireless charger, remote control toys, precision
instruments and meters, automobile industry, medical equipment, consumer
electronics, household appliances, electric glass doors and Windows, etc., wide
application range
Method
of use: the best stable in horizontal plane, installed on the 3D Printing Motor output
shaft parts, cannot use a hammer to knock, knock prone to press into the 3D Printing Motor drive, may cause damage to internal components, and cannot be used in the
case of blocked.
Operating temperature range:
3D Printing Motor should be used at a temperature of -10~60℃.
The figures stated in the catalog specifications are based on use at ordinary room temperature catalog specifications re based on use at ordinary room temperature (approximately20~25℃.
If a 3D Printing Motor is used outside the prescribed temperature range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.Depending on the temperature conditions ,it may be possible to deal with them by changing the grease of the motor's parts.Please feel free to consult with us about this.
Storage temperature range:
3D Printing Motor should be stored ta a temperature of -15~65℃.
In case of storage outside this range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.
Service life:
â—Use with a load that exceeds the rated torque
â—Frequent starting
â—Momentary reversals of turning direction
â—Impact loads
â—Long-term continuous operation
â—Forced turning using the output shaft
â—Use in which the permitted overhang load or the permitted thrust load is exceeded
â—A pulse drive ,e.g.,a short break,counter electromotive force,PWM control
â—Use of a voltage that is nonstandard as regards the rated voltage
â—Use outside the prescribed temperature or relative-humidity range,or in a special environment.
â—Please consult with us about these or any other conditions of use that may apply,so that we can be sure that you select the most appropriate model.
when it come to volume production,we're a
major player as well .each month,we rurn out
600000 units,all of which are compliant with the rohs directive.Have any
questions or special needed, please contact us, we have the engineer group and
best sales department to service to you Looking forward to your inquiry. Welcome to
our factory.
3D Printing Motor,3D Printing Gear Motor,3D Printing Pen Motor,3D Printing Spindle Motor Shenzhen Shunchang Motor Co., LTD. , https://www.scgearmotor.com
Product overview
++++General
Farady offers a complete range of distribution transformers designed to grant the reliability, durability, and efficiency required in utility, industrial, and commercial applications. Farady's liquid-filled transformers are manufactured in accordance with the most demanding industry and international standards. Compliance with important standards, from IEC to VDE, is a matter of course, just as much as the exclusive use
of high-quality materials. Qualified employees implement the demanding standards in daily practice.
++++Standard Features
1,Product Range:15kVA-10000kVA, up to 44kV
2, System voltage: max. 36 kVA 200 BIL
3,Coolers: corrugated wall or radiator
4,Oil preservation: hermetically sealed or conservator/free breathing
5, Tap changer: off-circuit or on-load
6, Cooling medium: mineral oil, Midel
7, Steel type core clamping system
8, High voltage (HV) multilayer winding
9, Low voltage (LV) foil winding or layer winding
10, Winding materials aluminium or copper
11,High temperature class transformers
12,Low noise solution
13,Efficient transformers with reduced losses
14, Liquid-filled
15,Used in special conditions
16,Sophisticated facilities
17, Usage of wooden case
18, 3D package for drawings
19, Special test like Zero Sequence Impendence test
20, Cooling: ONAN, ONAN/ONAF, KFAF, KFW
++++Service condition
a) Suitable for indoor or outdoor application
b)Air temperature: Maximum temperature: +40ºC; Minimum temperature:-30ºC
c) Humidity: Monthly average humidity 95%; Daily average humidity 90% .
d) Altitude above sea level: Maximum installation altitude: 2000m.
e)Max wind speed:35M/s
f) Ambient air not apparently polluted by corrosive and flammable gas, vapor etc.
g) No frequent violent shake
Note: * Beyond those services condition should enquiry to manufacturer technical dept during order
++++ Tests
1,  Voltage ratio. Polarity and phase relationship test on each tapping
2,  Resistance of all windings
3, No-load current and no-load losses measurement
4,  Load losses measurement at rated current and frequency
5,  Impedance voltage measurement
6,  Induced over-voltage and separate source voltage withstand tests
7, Impulse voltage withstand test.
8,  Noise level test
9,  Oil leakage test
10, Overload test at 150% rated current for one hour after temperature rise test and hot resistance measurement of (HV - LV)
Rated PowerÂ
Load losses
No-load losses
No load current%
Impedance%Â
S11-30
630
100
2.1
4
S11-50
910
130
2
4
S11-63
1090
150
1.9
4
S11-80
1310
180
1.8
4
S11-100
1580
200
1.6
4
S11-125
1890
240
1.5
4
S11-160
2310
270
1.4
4
S11-200
2730
330
1.3
4
S11-250
3200
400
1.2
4
S11-315
3830
480
1.1
4
S11-400
4520
570
1
4
S11-500
5410
680
1
4
S11-630
6200
810
0.9
4.5
S11-800
7500
980
0.8
4.5
S11-1000
10300
1150
0.7
4.5
S11-1250
12000
1360
0.6
4.5
S11-1600
14500
1640
0.6
4.5
Â
Whether in design, manufacturing methods   or materials the cores of Farady transformers represent the latest state of technology. The   silicon alloyed electric sheet steel used is grain-oriented, cold-rolled and insulated on both sides, guaranteeing low losses and noise and these values are even improved by laser treatment. Numerically controlled cutting machines provide for careful treatment in the cutting process in order to avoid mechanical tension in the core and thus unwanted properties right from the beginning. Standard use of step-lap cutting additionally minimizes losses and noise.
Â
Company Information
We are professional manufacturer of power transformer,electrical transformer,step voltage regulator,oil immersed and cast resin dry type transformer
ISO9001&14001 approval company
Each series transformer we manufacutured was type tested
Professional technical team ensure our product was always advanced amony your competitor
Founded in 2006, with a registered capital of 10 million USD, Zhejiang Farady Electric enjoys about 10 years experience in distribution transformer manufacture.
Farady is located in Liushi of Yueqing, a costal city, which is often referred as the Electric Products Capital in China. Boardered by the State road, highway, and high-speed railway, close to
SHANGHAI/NINGBO/WENZHOU sea ports, and the Yongqiang International airport in Wenzhou, we enjoy a great advantage in transportation which thus can guarantee our clients the fast shipping.
Our main products include: step voltage regulator up to 35kV, conventional and complete self-protection transformer, single phase pad mounted transformer, withstand high overload transformer, capacity-adjustable transformer, amorphous transformer, energy-saving transformer, etc green transformer. All the products of ours have passed the national laboratory type test, which also wins the STATE GRID of China as one of our contractors.
The company is equipped with the state-of-the-art technology, sophisticated facilities, ISO9001 quality management system certification and ISO14001 environment certification approval.
We also enjoy the Certification of New Hi-tech Enterprises, National Spark Program, and own more than 70 item transformer patents, with which our products are not only popular in the domestic market but also exported to Southeast Asia, South America, Africa and the middle east.
Today, boasting the value of products specialization, brand management, and business globalization, with the sprits of pragmatism, innovation, efficiency, and responsibility, Farady Company is dedicated to become the biggest name in the international business of transformers in China, and contributes its share to the transformation from the Made in China into the Invented in China.
Pckaging&Shipping
 Long time shipment & Seaworthy wooden box
Wooden package optional:
1,choose one unit/ wooden box
2,choose 2unit/ wooden box to save cost
FAQ
1,Why I buy Farady transformer
Â
After compare quality,delivery and price you will find out answer
Â
2,How is your farady electrical transformer waranty
Â
12+12month after manufacture date,you total got 2 year waranty
Â
3,Is that possible to be one of distributor of Farady Electric in my country
Â
Yes,once you action is fast enough
Â
4,More question......
Â
Feel free to contact you you will get immediately reply
Our services
1,Quick response in before sales period help you got order
Â
2,Excellent service in production time let you know each step we made
Â
3,Reliable quality solve you aftersale headache
Â
4,Long quality waranty ensure you can buy without hesitate
Step Down Transformer Copper Core Oil Immersed Copper Products
Model NO.: S11
Usage: Power Transformer
Frequency Characteristics: Power Frequency
Shape of Core: Ring
Brand: Farady
Item: Transformer Copper Core Products
Transformer: Transformer Copper Core
Rating Capacity: 5000 kVA
Frequency: 50Hz/60Hz
Tap Changer: off Load Tap Changer
Material: CRGO,Copper,Minral Oil
Tank Design: Sealed
Package: Wooden Case
Loss: Low Losses
Coil Structure: Isolation
Trademark: Farady
Specification: CTOC type tested
Origin: Zhejiang China
HS Code: 85042100
step down transformer copper core oil immersed copper products